Carburettor needle for PHVA/PHBN carburettors The throttle needle, together with the mixing tube, regulates the composition of the mixture in the part-load or half-throttle range. Needles vary in diameter, length & pitch, with each of these aspects having a specific influence on the mixture composition. Generally speaking, a thicker needle results in a leaner mixture. A longer needle causes the mixture to be richer. The needle also has four clip positions that can be used to adjust its position. The higher the clip is positioned on the needle, the deeper the needle dips into the mixing tube, resulting in a leaner mixture in the half-throttle range. If the needle is already in the lowest position & the mixture is still too rich (recognisable, for example, by the four-stroke with the slide half open), you should consider a thicker needle or a smaller mixing tube. OEM numbers (for comparison purposes): B16250.011 (MALOSSI) 1625011 08 (DELLORTO)   Article: Dell Orto DELLORTO Conical... ...

Carburettor needle for PHVA/PHBN carburettors The throttle needle, together with the mixing tube, regulates the composition of the mixture in the part-load or half-throttle range. Needles vary in diameter, length & pitch, with each of these aspects having a specific influence on the mixture composition. Generally speaking, a thicker needle results in a leaner mixture. A longer needle causes the mixture to be richer. The needle also has four clip positions that can be used to adjust its position. The higher the clip is positioned on the needle, the deeper the needle dips into the mixing tube, resulting in a leaner mixture in the half-throttle range. If the needle is already in the lowest position & the mixture is still too rich (recognisable, for example, by the four-stroke with the slide half open), you should consider a thicker needle or a smaller mixing tube. OEM numbers (for comparison purposes): B16250.013 (MALOSSI) 1625013 08 (DELLORTO)   Article: Dell Orto DELLORTO Conical... ...

Carburettor needle for PHVA/PHBN carburettors The throttle needle, together with the mixing tube, regulates the composition of the mixture in the part-load or half-throttle range. Needles vary in diameter, length & pitch, with each of these aspects having a specific influence on the mixture composition. Generally speaking, a thicker needle results in a leaner mixture. A longer needle causes the mixture to be richer. The needle also has four clip positions that can be used to adjust its position. The higher the clip is positioned on the needle, the deeper the needle dips into the mixing tube, resulting in a leaner mixture in the half-throttle range. If the needle is already in the lowest position & the mixture is still too rich (recognisable, for example, by the four-stroke with the slide half open), you should consider a thicker needle or a smaller mixing tube. OEM numbers (for comparison purposes): B16250B014 (MALOSSI) 1625014 08 (DELLORTO)   Article: Dell Orto DELLORTO Conical... ...

Dell' Orto ECU ECS original version for SYM Symphony & Peugeot Tweet 25km/h 50cc 4-stroke Euro 4 carburettor from 2017 to 2020 Version especially for vehicles 25km/h Article: Dell Orto DELLORTO ECU ECS Original 25km/h ...

ECU ECS original version for SYM Orbit II / X' Pro / Crox / Fiddle II / At 25km / h 50cc 4-stroke Euro 4 carburettor from 2018 to 2020   SYM OEM 1640A-AW2-000 Version especially for vehicles 25km/h Article: Dell Orto DELLORTO ECU ECS Original 25km/h ...

This DENALI Data Dim™ Dual-Intensity Controller enables the DENALI lights to switch between half & full intensity with your vehicle’s original high beam switch. All DENALI 2.0 Light pods are equipped with a dedicated 3rd-wire dimming circuit so an external signal can reliably control the intensity of the LED chip at the source.   This will allow you (for example) to couple your dipped-beam headlamps to 50% mode & your main beam to 100% mode.   Warning, if you want to control the intensity of your lights separately from the rest of your equipment, you will need to install the 3 position switch 30500042 Article: DENALI 2.0 Data Dim Dual Intensity Controller ...

This 3-position switch replaces your standard On/ Off switch (supplied with your DENALI lights) to allow you to use your additional lights at 50% or 100% light intensity.   * Construction Dry Seal™ totally waterproof * Mounting with 3M adhesive included * Plug& Play installation on all DENALI 2.0 bundles   Note: Requires the DENALI Dual-Intensity Controller 30500042   What’s In The Box:   * (x 1) Dry Seal™ HI-LOW-OFF waterproof switch * (x 1) adhesive pad Article: DENALI 2.0 High/ Low/ Off Sealed Switch ...

Delivered as standard with the DENALI 2.0 light kits, this switch is ideal for controlling all kinds of electrical accessories on your machine.   * Two-position On/ Off switch * Green indicator light in On position * Tolerates up to 15 amps * Fully waterproof Dry Seal™ construction, withstands total immersion * Mounting by 3M adhesive or on handlebars from 22 to 25 mm (required included) Article: DENALI 2.0 On/ Off Sealed Switch ...

The Denali 2.0 Sealed Micro Relay is a replacement for the standard DENALI 2.0 Premium 3-pin harness. Article: DENALI 2.0 Sealed Micro Relay ...

If you no longer want to bother with additional switches on the handlebars, install the DENALI Switch Eliminator Plug! It connects in a few seconds to the DENALI 2.0 beams on the socket provided for the switch, as soon as you turn the ignition on, your lights come on.   This accessory can be combined with the Data Dim Dual Intensity to achieve operation of the type: dipped-beam headlamps on -> 50% additional headlamps / high beam on -> 100% additional headlamps.   Can be placed or removed in a few seconds from the beam, you can adapt your assembly to suit your needs. Removing the switch is particularly interesting in road rallies where managing the switching on/off of the lights can waste precious seconds. Article: DENALI 2.0 Switch Eliminator Plug ...