Dell' Orto ECS solenoid valve filter, for Lambretta, Kymco, Peugeot & SYM 50cc 4-stroke Euro 4 & Euro 5 scooters, from 2017-. Lambretta OEM 33302-LKB0-000 Kymco OEM 18800-ACH5-E10 Peugeot OEM 804403 SYM OEM 18663-XFA-000 Article: Dell Orto DELLORTO Solenoid Valve Filter Euro 4 Euro 5 ...

This DENALI Data Dim™ Dual-Intensity Controller enables the DENALI lights to switch between half & full intensity with your vehicle’s original high beam switch. All DENALI 2.0 Light pods are equipped with a dedicated 3rd-wire dimming circuit so an external signal can reliably control the intensity of the LED chip at the source.   This will allow you (for example) to couple your dipped-beam headlamps to 50% mode & your main beam to 100% mode.   Warning, if you want to control the intensity of your lights separately from the rest of your equipment, you will need to install the 3 position switch 30500042 Article: DENALI 2.0 Data Dim Dual Intensity Controller ...

This 3-position switch replaces your standard On/ Off switch (supplied with your DENALI lights) to allow you to use your additional lights at 50% or 100% light intensity.   * Construction Dry Seal™ totally waterproof * Mounting with 3M adhesive included * Plug& Play installation on all DENALI 2.0 bundles   Note: Requires the DENALI Dual-Intensity Controller 30500042   What’s In The Box:   * (x 1) Dry Seal™ HI-LOW-OFF waterproof switch * (x 1) adhesive pad Article: DENALI 2.0 High/ Low/ Off Sealed Switch ...

Delivered as standard with the DENALI 2.0 light kits, this switch is ideal for controlling all kinds of electrical accessories on your machine.   * Two-position On/ Off switch * Green indicator light in On position * Tolerates up to 15 amps * Fully waterproof Dry Seal™ construction, withstands total immersion * Mounting by 3M adhesive or on handlebars from 22 to 25 mm (required included) Article: DENALI 2.0 On/ Off Sealed Switch ...

The Denali 2.0 Sealed Micro Relay is a replacement for the standard DENALI 2.0 Premium 3-pin harness. Article: DENALI 2.0 Sealed Micro Relay ...

The DENALI 2.0 perch switch mount kit is used to fit the switches to your clutch or brake perch. The kit

Includes::

...

This DENALI MT Series 3-Pin Male Waterproof Connector Pigtail can be used to adapt other brands of lighting or accessories to the DENALI CANsmart Controller or 2.0 Premium Wiring Harness. The connector is pre-assembled with 3 inch 18 AWG wires exiting the connector which can be soldered onto the light or accessory of your choice. Article: DENALI 3 pin Male Connector, Size 30 mm Article: DENALI 3 pin Male Connector, Size 30 mm, Size 30 mm ...

This DENALI DRL wiring harness kit features high-quality waterproof components & is designed to power two DENALI DRL Light Pods. It features low profile, water tight connectors & high quality molded wire to ensure moisture is kept out of the system. The harness

Includes:: a completely sealed, waterproof switch that was engineered from the ground up to withstand harsh conditions on powersports vehicles. It’s clever design can be either flush or bar mounted. The switch enables independent dimming of the lights, separate from the vehicle's OEM lighting system.    What's In The Box?   * (x 1) DRL Harness * (x 1) Hi-Low-Off Switch * (x 1) ⅞” Handlebar Switch Mount   Article: DENALI 3 Way Switch with Wiring Harness

...

3-pin waterproof connector, pigtail, female This DENALI MT series 3-pin waterproof connector pigtail can be used to modify, customise or replace electrical connections. The connector is pre-assembled with 3-inch 18 AWG wires that exit the connector & can be attached to the light fixture or accessory of your choice. Article: DENALI 3-pin Waterproof Connector, Pigtail, Female ...

The B6 LED brake light was purpose built to create the most amount of light from the most compact, low-profile housing possible. Six 1-watt Light Emitting Diodes generate enhanced visibility with minimal bulk. Newly updated to operate as both a brake light & running light, the B6 provides enhanced functionality on conventional motorcycles as well as those that can use the advanced features of the CANsmart Controller (sold separately). Note that flash patterns & deceleration activated “auto brake light” functionality is only available when used in conjunction with the DENALI CANsmart Controller.  

Features:   * Six extremely bright LEDs * Low 6 watt power consumption * Running light * Brake light * License plate light * Low profile design * Easy to wire to existing brake & running light circuits * Compatible with DENALI CANsmart Controller (sold separately)   Additional Features Article: DENALI B6 License Plate Brake Light

...