More From Contributor

Used to install or remove bearing bottom brackets on the majority of bikes fitted with 16-notch external bearing threaded cups. The splines engage securely onto the bottom bracket notches allowing for easy removal or tightening of the cups, without the risk of the tool slipping. It also features an adjustment cap tool for removing & adjusting the end caps on Shimano Hollow Tech II cranks. ...

Available

Designed to access the narrow spaces behind the chainset, this low profile chainring nut spanner holds the nut still to prevent it from turning when tightening or loosening the chainring bolt using a Hex or Star key. ...

Available

Badly adjusted or loose cone nuts can cause unnecessary wear & damage to both the wheel bearings & inner hub components. These super slim cone spanners allow for the cone nuts to be tightened hard up against the axle lock nuts so that they don't then come undone taking the hub bearings back out of adjustment. This set covers the 4 most popular sizes & are long enough to provide a good amount of leverage. ...

Available

For use when removing & installing sprockets & cassettes. A chain whip, also known as a sprocket remover or a sprocket holder, is used to hold the cogs on the rear wheel in place as a lockring tool is used to undo the cassette in the opposite direction. ...

Available

This crank extractor is used for the correct removal of crank arms & chainsets that use a square-tapered, or splined ISIS Drive, bottom bracket. The threaded collar screws into the crank arm before the drive bolt gently forces the bottom bracket axle away from the tool & out of the crank arm. It also features a 14mm socket at one end for the removal of the crank bolt/nut. ...

Available

This adjustable bike stand holds onto the rear wheel fixings, supporting the bike in an upright position, providing a safe way to store or display a bicycle without having to lean it against anything else, as well as providing a simple & steady work st&. The rear wheel can be set so that it is raised off the ground, enabling the rear wheel to be rotated allowing the gears to be checked & adjusted, chain & drivetrain cleaned & the rear wheel inspected to see if it is running true. ...

Available

Ideal for use when fitting or adjusting brake cables, these cable pullers act as an extra pair of hands to grip & hold a cable in position whilst the pinch bolt is being tightened. The thumb lock allows for one-handed operation, helping to ensure the cable is tensioned correctly first time, minimising any potential damage caused to the cable by having to repeatedly clamp & readjust it. ...

Available

Designed to keep bars steady & inline while carrying out maintenance on a bicycle. This handlebar holder is ideal for when the bike is being hung in a workst&. By hooking over both the top tube & the bars it prevents the front of the bike from turning whilst being worked on. ...

Available

Tube cutter for fork steerer tubes, handlebars, seat posts, or any round tubing up to 31.75mm (1 1/4") diameter, this tool ensures a professional & accurate cut every time. The internal contact points on the guide are non-scratching nylon & support the tube being cut so that it's not crushed or damaged. It is designed to be clamped in a bench vice allowing the user both hands to steady the cutting process. ...

Available

Designed to remove & refit both Schrader & Presta type valve cores, this tool is a must when adding tyre sealant, fitting a Presta valve extender or replacing a valve core. Despite its small diameter, the knurled finish provides the grip needed to loosen & tighten the valve without requiring additional tools. Due to its compact size it would make for a great addition to any cyclists tool kit when out on a ride, especially when running a tubeless set up. ...

Available

Laser Laser 8174 LTR Internal Cable Routing Tool

For use when having to guide new cables through an internally routed frame, this kit uses magnets to make light work of a task that can be both time-consuming and frustrating. It comes supplied with adaptors to fit inner gear & brake cables, Shimano Di2 wires (e-Tube cables), outer gear & brake housing, and hydraulic brake lines

Availability: In Stock
Supplier: Machine Mart
SKU: 040218174

Description Reviews / Comments Add New

Product Description

Reviews/Comments

Add New

Intelligent Comparison

Available

Laser Laser 8179 LTR Valve Core Removal Tool Machine Mart

£7.99

Supplier Information

Machine Mart

Get the job done with Machine Mart (http://www.machinemart.co.uk)! Explore our extensive range of power tools, hand tools, workshop equipment, and more, designed to tackle any DIY project or professional task with ease. From robust drills and saws to sturdy workbenches and storage solutions, we provide everything you need to build, repair, and maintain your home or workplace. With top brands like DeWalt, Makita, and Clarke, you can trust in quality and reliability. Plus, enjoy expert advice, unbeatable prices, and convenient delivery options. Shop now and unleash your potential with Machine Mart!

More From Contributor

Laser Laser 8174 LTR Internal Cable Routing Tool

Product Description

Reviews/Comments

Add New

Intelligent Comparison

Price History

Vouchers

Facebook

Jargon Buster

Supplier Information

Community Generated Product Tags

Contact Us

Information

My Account