More From Contributor

For use when removing & installing sprockets & cassettes. A chain whip, also known as a sprocket remover or a sprocket holder, is used to hold the cogs on the rear wheel in place as a lockring tool is used to undo the cassette in the opposite direction. ...

Available

This crank extractor is used for the correct removal of crank arms & chainsets that use a square-tapered, or splined ISIS Drive, bottom bracket. The threaded collar screws into the crank arm before the drive bolt gently forces the bottom bracket axle away from the tool & out of the crank arm. It also features a 14mm socket at one end for the removal of the crank bolt/nut. ...

Available

For use when having to guide new cables through an internally routed frame, this kit uses magnets to make light work of a task that can be both time-consuming & frustrating. It comes supplied with adaptors to fit inner gear & brake cables, Shimano Di 2 wires (e-Tube cables), outer gear & brake housing, & hydraulic brake lines ...

Available

This adjustable bike stand holds onto the rear wheel fixings, supporting the bike in an upright position, providing a safe way to store or display a bicycle without having to lean it against anything else, as well as providing a simple & steady work st&. The rear wheel can be set so that it is raised off the ground, enabling the rear wheel to be rotated allowing the gears to be checked & adjusted, chain & drivetrain cleaned & the rear wheel inspected to see if it is running true. ...

Available

Ideal for use when fitting or adjusting brake cables, these cable pullers act as an extra pair of hands to grip & hold a cable in position whilst the pinch bolt is being tightened. The thumb lock allows for one-handed operation, helping to ensure the cable is tensioned correctly first time, minimising any potential damage caused to the cable by having to repeatedly clamp & readjust it. ...

Available

Tube cutter for fork steerer tubes, handlebars, seat posts, or any round tubing up to 31.75mm (1 1/4") diameter, this tool ensures a professional & accurate cut every time. The internal contact points on the guide are non-scratching nylon & support the tube being cut so that it's not crushed or damaged. It is designed to be clamped in a bench vice allowing the user both hands to steady the cutting process. ...

Available

Designed to remove & refit both Schrader & Presta type valve cores, this tool is a must when adding tyre sealant, fitting a Presta valve extender or replacing a valve core. Despite its small diameter, the knurled finish provides the grip needed to loosen & tighten the valve without requiring additional tools. Due to its compact size it would make for a great addition to any cyclists tool kit when out on a ride, especially when running a tubeless set up. ...

Available

Recommended for use when lacing spokes into a bicycle wheel, this spoke nipple driver allows for nipples to be fitted & tightened through the wheel rim at speed due to its clever cranked design. The head of the driver features a tab to fit into the spoke hole helping to hold the nipple in place whilst it is being offered up to the hole in the rim. Intended to be used to initially tighten the nipple until all the spokes are fitted & are starting to tension, at which point a spoke key can be used. ...

Available

A wheel alignment gauge (dishing tool), is essential for ensuring the wheel sits correctly in the frame or forks by allowing you to check that the rim is centred between the locking nuts on either side of the hub. ideal to be used when wheel building or truing a buckled wheel. ...

Available

These pliers are perfect for removing bicycle chains that use a master link. Due to the way master links fit together, they are kept in place by the chain being pulled tight whilst pedalling. This combined with wear, corrosion & grime can make them difficult to undo without the correct tool. These chain link pliers gently squeeze the master link together so that it opens allowing for the chain to be split & removed for maintenance, cleaning or replacement. ...

Available

Laser Laser 8177 LTR Handlebar Holder

Designed to keep bars steady and inline while carrying out maintenance on a bicycle. This handlebar holder is ideal for when the bike is being hung in a workstand. By hooking over both the top tube and the bars it prevents the front of the bike from turning whilst being worked on.

Availability: In Stock
Supplier: Machine Mart
SKU: 080828177

Description Reviews / Comments Add New

Product Description

Reviews/Comments

Add New

Intelligent Comparison

Available

Laser Laser 8195 LTR Handlebar Mirror Machine Mart

£6.38

Available

Laser Laser 8191 LTR Wall Mounted Bike Holder Machine Mart

£20.99

Available

Laser Laser 8176 LTR Cable Puller Pliers Machine Mart

£14.98

Available

Laser Laser 8221 LTR Cable Cutters Machine Mart

£13.99

Supplier Information

Machine Mart

Get the job done with Machine Mart (http://www.machinemart.co.uk)! Explore our extensive range of power tools, hand tools, workshop equipment, and more, designed to tackle any DIY project or professional task with ease. From robust drills and saws to sturdy workbenches and storage solutions, we provide everything you need to build, repair, and maintain your home or workplace. With top brands like DeWalt, Makita, and Clarke, you can trust in quality and reliability. Plus, enjoy expert advice, unbeatable prices, and convenient delivery options. Shop now and unleash your potential with Machine Mart!

More From Contributor

Laser Laser 8177 LTR Handlebar Holder

Product Description

Reviews/Comments

Add New

Intelligent Comparison

Price History

Vouchers

Facebook

Jargon Buster

Supplier Information

Community Generated Product Tags

Contact Us

Information

My Account